Products

High quality materials with exceptional, extended performance.
pro-tech bucket on job site
Jump to
PRoducts
Product Ratings
Warranty Guide
A-P Primer

A-P Primer is a low solids water-based 100% acrylic primer designed to properly prepare a variety of roofing substrates prior to the installation of spray polyurethane foam and acrylic elastomeric topcoats. This cost effective primer has outstanding adhesion qualities and is also effective in cooler climate conditions for creating heat gain into substrates to maximize yield of spray polyurethane foam.

Sizes

5 gallon, 55 gallon, 275 gallon

EC-100

EC-100 is a premium grade 100% acrylic elastomeric water-based coating designed specifically for use over new polyurethane foam roofing systems. This durable 100% acrylic coating possesses excellent dirt pick-up resistance and outstanding adhesion, weatherability and good ponded water resistance over sprayed-inplace polyurethane foam surfaces.

Sizes

5 gallon, 55 gallon, 275 gallon

EC-50 NR

EC-50 NR (Non Rated) is a cost effective 100% acrylic elastomeric water-based coating designed specifically for use over new polyurethane foam roofing systems. This durable 100% acrylic coating possesses excellent dirt pick-up resistance and outstanding adhesion, weatherability, ultraviolet and good ponded water resistance over sprayed-in-place polyurethane foam surfaces.

Sizes

55 gallon, 275 gallon

Modified Asphalt Primer

Modified Asphalt Primer is an acrylic modified asphalt primer designed for use over various existing roofing substrates. This cost effective primer has outstanding adhesion characteristics.

Sizes

5 gallon, 55 gallone, 275 gallon

Pro-Tech Cleaner Concentrate

Pro-Tech Cleaning Concentrate is a 100% biodegradable cleaning agent diluted at a 10:1 ratio with water to effectively remove dirt and other surface contaminates from a variety of existing surfaces. This environmentally safe cleaning agent will not harm animal life, ground vegetation or its inhabitants.

Sizes

1 gallon

Pro-Tech Spray Polyurethane Foam System - Roofing Applications

PRO-TECH URETHANE P-2.8 is a two-part system designed for roofing applications where the compressive strength (55 psi) provides a greater resistance to foam fracture than is offered by foams of lower density. PRO-TECH Urethane P-2.8 has been formulated with HFC 245 FA as the blowing agent.

Sizes

55 gallon, 275 gallon

Pro-White High Tensile

Pro-White is a premium grade 100% acrylic elastomeric water-based high tensile coating designed specifically for use over new polyurethane foam roofing systems. This durable 100% high tensile acrylic coating combines abrasion and hail resistance along with excellent dirt pick-up resistance, outstanding adhesion, weatherability, ultraviolet and good ponded water resistance over spayed-in-place polyurethane foam surfaces.

Sizes

5 gallon, 55 gallon, 275 gallon

Super Putty

Super Putty is a premium grade acrylic elastomeric water-based compound which combines acrylic polymers with high solids content. This durable acrylic patching compound has outstanding adhesion, elongation, and weatherability and can be applied to a variety of roofing surfaces.

Sizes

2 gallon

Superiorseal

Superiorseal Topcoat is a high quality co-polymer acrylic elastomeric water-based coating designed for use over various new and existing roofing substrates. This quality elastomeric coating is a durable, long lasting, ultraviolet resistant topcoat with good dirt pick up resistance.

Sizes

5 gallon, 55 gallon, 275 gallon

Techguard Cementitious - Topped Foam Roofing System

TechGuard Cementitous Topped Urethane P 2.8 is a two part system designed for roofing applications where the compressive strength (54 psi) provides a greater resistance to foam fracture than is offered by foams of lower density. The foam is coated with EC- 100 usually in two to three coats at a rate of 1 ¼ gallons per 100 square feet per coat. A crushed #6 limestone is applied to all flat areas in the wet final acrylic elastomer coating at approximately 60 lbs. per 100 square feet. Finally an acrylic modified cementitous top coat is spray applied in two coats achieving a total of 7 to 8 gallons per 100 square feet to all flat areas and allowed to dry.

Sizes

55 gallon, 275 gallon

Tietex Roof Fabric

TIETEX is a stitch-bonded polyester used to help fill in low spots and indentations in the roof. Stitch-bonding offers a rare combination of high strength properties with good elongation for outstanding thermal pressure force accommodations.

Sizes

3 oz./sq. yd. Available Widths: 40", 12", 6", 4"

Ultra Shield

Ultrashield Topcoat is a cost effective co-polymer acrylic elastomeric water-based coating designed for use over various new and existing roofing substrates. This low cost alternative elastomeric coating is a durable, yet ultraviolet resistant topcoat with good weatherability.

Sizes

5 gallon, 55 gallon, 275 gallon

Product Ratings

Pro-Tech Products, Inc. Roof Warranties

Coating Warranty

Warranty Type
Coverage
DFT (mills)
Cost
Inspection Requirements
7 Year Coating Product
Material/Labor
25
None
None
12 Year Coating Product
Material/Labor
30
None
None
15 Year Coating Product
Material/Labor
35
None
None

SYSTEM WARRANTY

Warranty Type
Coverage
DFT (mills)
Foam Thickness/Density
Cost
Inspection Requirements
10 Year Roof System
Material/Labor
27
Min. 1” / 2.8 lb.
None
None
15 Year Roof System
Material/Labor
40
Min. 1.5” / 2.8 lb.
None
None
20 Year Roof System
Material/Labor
45
Min. 2” / 3 lbs.
None
None

Pro-Tech Products Roof System is defined as Pro-Tech Products coated foam systems that meet or exceed building codes and are fully UL rated. ALL Roof System warranties require the use of Pro-Tech EC-100 or Pro-Tech Pro-White High Tensile coating.

The use of Cementitious topcoat is allowed in ADDITION to the above parameters. Coating millage must still be maintained according to table. For specific details involving the use of any of the above referenced warranties, consult the product data, application sheets, and specific warranty documents.

The warranty term is determined according to the coating dry film thickness (DFT) and foam thickness as set for in the charts above, NO EXCEPTIONS.

Warranty Forms

A completed warranty request form must be submitted before a warranty is issued. Please download and fill out the form below. Once you have completed filling out the form, please email it to: reception@pro-techproducts.com

If you have any questions:
Call: 480-945-7303
Email: info@pro-techproducts.com
Or contact us.

Experience the difference Pro-Tech Products can make. Contact us today!

Contact us